Proudly Made In The USA!!!
Dual Gauge Panel:
- Fits 1994-2000 Mustang
- Replaces lower CD Player or Storage Compartment
- Can also be used to replace upper CD Player or Cassette Deck
- Made to hold (2) 2-1/16" Autometer Gauges
- Made of 1/8" 6061 T6 Aluminum
- Machined, not stamped
- Comes In Natural Aluminum Finish or Powder Coated Finish
- Includes All Necessary Mounting Hardware & Instructions
- Does not require any modification to dash or trim
- Gauges not included
- Natural Aluminum Price:$49.99
- Part #:NFS # 100-1000
- Satin Black Powder Coated Price:$69.99
- Part # NFS # 100-1010
Triple Gauge Panel:
- Fits 1994-2000 Mustang
- Replaces lower CD Player or Storage Compartment
- Can also be used to replace upper CD Player or Cassette Deck
- Made to hold (3) 2-1/16" Autometer Gauges
- Made of 1/8" 6061 T6 Aluminum
- Machined, not stamped
- Comes In Natural Aluminum Finish or Powder Coated Finish
- Includes All Necessary Mounting Hardware & Instructions
- Does not require any modification to dash or trim
- Gauges not included
- Natural Aluminum Price:$49.99
- Part #:NFS # 100-1350
- Satin Black Powder Coated Price:$69.99
- Part # NFS # 100-1355
Quad Switch Panel:
- Fits 1994-2000 Mustang
- Replaces lower CD Player or Storage Compartment
- Can also be used to replace upper CD Player or Cassette Deck
- Includes (4) high quality 20 amp covered toggle switches
- Made of 1/8" 6061 T6 Aluminum
- Machined, not stamped
- Comes In Natural Aluminum Finish or Powder Coated Finish
- Includes All Necessary Mounting Hardware & Instructions
- Does not require any modification to dash or trim
- Natural Aluminum Price:$99.99
- Part #:NFS # 100-1015
- Satin Black Powder Coated Price:$119.99
- Part # NFS # 100-1025
Single Gauge/Dual Switch Panel:
- Fits 1994-2000 Mustang
- Replaces lower CD Player or Storage Compartment
- Can also be used to replace upper CD Player or Cassette Deck
- Made to hold (1) 2-1/16" Autometer Gauge
- Includes (2) high quality 20 amp covered toggle switches
- Made of 1/8" 6061 T6 Aluminum
- Machined, not stamped
- Comes In Natural Aluminum Finish or Powder Coated Finish
- Includes All Necessary Mounting Hardware & Instructions
- Does not require any modification to dash or trim
- Gauge not included
- Natural Aluminum Price:$69.99(Special:$49.99!!!)
- Part #:NFS # 100-1030
- Satin Black Powder Coated Price:$89.99
- Part # NFS # 100-1040
Blank Gauge/Switch Panel:
- Fits 1994-2000 Mustang
- Replaces lower CD Player or Storage Compartment
- Can also be used to replace upper CD Player or Cassette Deck
- Can be drilled to accommodate gauges, switches, accessories, etc.
- Made of 1/8" 6061 T6 Aluminum
- Machined, not stamped
- Comes In Natural Aluminum Finish or Powder Coated Finish
- Includes All Necessary Mounting Hardware & Instructions
- Does not require any modification to dash or trim
- Natural Aluminum Price:$39.99
- Part #:NFS # 100-1060
- Satin Black Powder Coated Price:$59.99
- Part # NFS # 100-1070
Coin Holder Switch Panel:
- Fits 1994-2004 Mustang
- Replaces coin holder or fog light switch
- Includes (1) high quality 20 amp covered toggle switch
- Made of 1/8" 6061 T6 Aluminum
- Machined, not stamped
- Comes In Natural Aluminum Finish or Powder Coated Finish
- Includes All Necessary Mounting Hardware & Instructions
- Requires very minor notching of coin holder cut-out for fitment. So minor that if the switch panel is removed and the coin holder is replaced, notches will not be visible.
- Natural Aluminum Price:$49.99
- Part #:NFS # 100-1045
- Satin Black Powder Coated Price:$69.99
- Part # NFS # 100-1055
Cup Holder Gauge Panel:
- Fits 2001-2004 Mustang. Will also fit the front/smaller diameter cup holder on 1998-2000 Mustang's, however, since 1998-2000 Mustang's feature a dual cup holder design, the wiring for the gauge may be visible through the rear/larger cup holder. Black wire loom will typically hide this.
- Fits in the smaller 3" I.D. Cup Holder in the center console
- Made to hold (1) 2-1/16" Autometer Gauge
- Made of 1/8" 6061 T6 Aluminum
- Machined, not stamped
- Comes In Natural Aluminum Finish or Powder Coated Finish
- Includes All Necessary Mounting Hardware & Instructions
- Requires (2) mounting holes to be drilled at the bottom of the Cup Holder, as well as (1) access hole at the bottom of the Cup Holder to run gauge wiring.
- Gauge not included
- Natural Aluminum Price:$49.99
- Part #:NFS # 100-1075
- Satin Black Powder Coated Price:$69.99
- Part # NFS # 100-1085
Cup Holder Switch Panel:
- Fits 2001-2004 Mustang. Will also fit the front/smaller diameter cup holder on 1998-2000 Mustang's, however, since 1998-2000 Mustang's feature a dual cup holder design, the wiring for the switches may be visible through the rear/larger cup holder. Black wire loom will typically hide this.
- Fits in the smaller 3" I.D. Cup Holder in the center console
- Includes (2) high quality 20 amp covered toggle switches
- Made of 1/8" 6061 T6 Aluminum
- Machined, not stamped
- Comes In Natural Aluminum Finish or Powder Coated Finish
- Includes All Necessary Mounting Hardware & Instructions
- Requires (2) mounting holes to be drilled at the bottom of the Cup Holder, as well as (1) access hole at the bottom of the Cup Holder to run switch wiring.
- Natural Aluminum Price:$59.99
- Part #:NFS # 100-1090
- Satin Black Powder Coated Price:$79.99(Special:$59.99!!!)
- Part # NFS # 100-1100
EGR Block-Off Plate:
- Made of 1/4" 6061 T6 Aluminum.
- Direct replacement for EGR Valve.
- We have one that fits 1996-2004 2V/4V Mustang and one that fits 1986-1995 5.0 Mustang.
- Matches contour of EGR mounting flange.
- Includes Ford EGR gasket and uses factory mounting hardware.
- Comes In Natural Aluminum Finish
- 1996-2004 2V/4V:Price:$24.99
- Part #:NFS # 100-1315
- 1986-1995 5.0:Price:$39.99
- Part #:NFS # 100-1320
Brake Cooling Kit:
- Gets the much needed air flow to the brake rotors and calipers on road race cars.
- Extends "on-track" rotor & brake pad life, and can eliminate "brake fade" on cars where high rotor, caliper, and brake fluid temperatures are a problem.
- Fits 1994-2004 Mustang Spindles.
- Backing Plates are made of 1/8" 6061 T6 Aluminum & Powder Coated Satin Black.
- The Backing Plates supplied replace your factory backing plates/dust shields. They have a unique design that points the airflow to the center of the rotor, where it should be, not the rotor surface, like most other brake cooling kits that are currently available!!!
- Includes stainless steel mounting hardware, stainless steel hose clamps, duct hose, and zip ties.
- Duct Hose is 3" I.D. and is available for Standard-Duty or Severe Duty use. Standard-Duty Duct Hose is Black, Single-Ply Neoprene and is good to 300 degrees. Severe-Duty Duct Hose is Orange/Red Double-Ply Silicone and is good to 600 degrees.
- Includes Installation Instructions.
- Please Note:This kit is more spindle specific as opposed to vehicle specific. It will fit 1994-2004 Mustang spindles. For example:For a 1999-2004 Cobra, the supplied duct hose will mount directly on to the factory brake vent hole in the front fascia, next to each fog light. For a 1994-1998 Cobra, we make a pair of Fog Light Adapter Brackets that will take the place of the fog light assembly. It will bolt to the back side of the bumper support just like the fog light mounting bracket. The back side will have a place for the Duct Hose to attach to, and the front side is tapered to match the diameter of the fog light opening. These adapter brackets will also work for Mustang GT's, V6's, & Mach 1's, even though the fog light openings are rectangular. The Fog Light Adapter Brackets are not centered in the rectangular opening, but they do still get airflow to them. For some 1999+ Mustang's, new mounting holes in the bumper support may need to be added. We have also used these on 1987-1993 Mustang GT front fascia's with success. New mounting holes need to be drilled in the bracket, but other than that they work great.
- Please Note:Depending on the length of your strut mounting bolts, you may need to slightly notch the duct hose mounting pipe for clearance.
- Price w/ Standard-Duty Duct Hose:$199.99
- Part #:NFS # 100-1400
- Price w/ Severe-Duty Duct Hose:$259.99
- Part #:NFS # 100-1405
- Price w/o Duct Hose:$149.99
- Part #:NFS #100-1410
- Price For Standard-Duty Duct Hose Only-(2) 3" I.D. x 4' Long:$69.99
- Part # NFS # 100-1415
- Price For Severe-Duty Duct Hose Only-(2) 3" I.D. x 4' Long:$99.99
- Part # NFS # 100-1420
- Price For Fog Light Adapter Brackets-Pair:$149.99
- Part # NFS # 100-1425
Brake Duct Backing Plates shown above.
Fog Light Adapter Brackets shown above.
4.2 F-150 Supercharger Kit:
- Custom made supercharger kit for 1997-2004 4.2 F-150's.
- This kit is complete and includes Vortech's V2 SQ Supercharger, Cast Aluminum Mounting Bracket, Fuel Management Unit, High Volume External Fuel Pump, Custom Machined Alternator Relocation Bracket, Powder Coated Discharge Tube, K&N Air Filter, and all necessary belts, hoses, hardware & instruction manual.
- Kit output is 8-10 PSI.
- Horsepower increase expected is 80-90 hp.
- 1997-2004 4.2 F-150 Supercharger Kit-Satin Price:$3499.99
- Part # NFS # 200-5000
- 1997-2004 4.2 F-150 Supercharger Kit-Polished Price:$3699.99
- Part # NFS # 200-5100
- NEW...1997-2004 4.2 F-150 Supercharger Custom Machined Alternator Relocation Bracket w/ Mounting Hardware & Silver Powder Coated Discharge Tube:$399.99
- Part # NFS # 200-5000IK
4.2 F-150 Supercharger installed shown above.